• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print

Home > Radar Maintenance and Parts Manuals > > Removal/Replacement Procedures - TM-11-5840-360-14-1-10185
Figure 5-2 Receiver Transmitter RT-1240 Troubleshooting Chart (Sheet 4 of 4)
Alignment Procedures - TM-11-5840-360-14-1-10186

TM-11-5840-360-14-1-1 Radar Set AN/SPS-64(V)5 (NSN 5840-01-034-3946) Manual
Page Navigation
  173    174    175    176    177  178  179    180    181    182    183  
TM 11-5840-360-14-1-1
5.10.2 Removal/Replacement Procedures
1. Insure removal of power from the unit per
Before initiating any removal or replacement activity
paragraph 5.10.2.
at Receiver Transmitter RT-1240, insure that all power
2. Remove front cover; loosen control panel
is removed from the equipment by performing the
captive screws and swing control panel into its service
following steps:
position.
1. Insure that POWER switch is set to OFF at
WARNING
associated (master) Indicator.
RESIDUAL
HIGH
VOLTAGE
2. Set LOCAL TEST switch to OFF.
CHARGES  MAY  BE  PRESENT.
3. Turn off ships circuit breakers which supply
DISCIIARGE
ALL
MAGNETRON
power to Receiver Transmitter RT-1240 under test.
TUBE
TERMINALS
AND
ALL
NOTE 1:
COMPONENTS IN THE VICINITY OF
When the Receiver Transmitter cover
THE MAGNETRON TUBE BEFORE
is  removed,  the  high  voltage
TOUCHING.
interlock
switch
automatically
3. Disconnect filament plug (potted wire terminals).
springs to a power disable position.
4. Loosen the alien screws on the tuning rod and
Power may be restored to the unit
disconnect the rod.
with the cover removed by pulling
5. Remove  the  six  screws,  washers  and
the interlock switch outward.
lockwashers and lift the magnetron oscillator out.
6. Reinstall using the reverse of above.
CAUTION
5.10.2.3 T/R Limiter V3.  - See Figure 5-1; refer to
ONLY
NON-FERROUS
TOOLS
assembly drawings in Chapter 6, Section 6.2 as
SHOULD BE USED WHEN WORK IS
necessary.
BEING PERFORMED INSIDE THE
1. Insure removal of power from the unit per
RECEIVER  TRANSMITTER  UNIT.
paragraph 5.10.2.
EXAMPLES
OF
NONFERROUS
2. Remove front cover; loosen control panel
MATERIALS
ARE
STAINLESS
captive screws and swing control panel into its service
STEEL, ALUMINUM OR BERRYLIUM
position.
COPPER.
WARNING
5.10.2.1 Modulator Tube V1. - See Figure 5-1; refer to
RESIDUAL
HIGH
VOLTAGE
assembly drawings in Chapter 6, Section 6.2 as
CHARGES  MAY  BE  PRESENT.
necessary.
DISCHARGE ALL COMPONENTS IN
1. Insure removal of power from the unit per
THE VICINITY OF THE T/R LIMITER
paragraph 5.10.2.
BEFORE TOUCHING.
2. Remove front cover; loosen control panel
3. Remove  the  IF  Amplifier  Assembly  per
captive screws and swing control panel into its service
paragraph 5.10.2.7. Steps 1,2,3,6.
position.
4. Remove  the  four  screws,  washers  and
WARNING
lockwashers that attach the T/R limiter to the duplexer
RESIDUAL
HIGH
VOLTAGE
assembly. Note orientation of the T/R limiter.
CHARGES  MAY  BE  PRESENT.
5. Remove the four screws, nuts and washers that
DISCHARGE
ALL
MODULATOR
attach the T/R limiter to the waveguide flange and
TUBE
TERMINALS
AND
ALL
remove the T/R limiter.
COMPONENTS IN THE VICINITY OF
6. Reinstall  new  T  R  Limiter  with  correct
THE MODULATOR TUBE BEFORE
orientation using the reverse of the above.
TOUCHING.
5.10.2.4 Local Oscillator Assembly X2. - See Figure 5-
3. Remove the screw and washer, located on the
1; refer to assembly drawings in Chapter 6, Section 6.2
left-hand outer side of the cabinet, that retains the nylon
as necessary.
rod, supporting spring and tube cap.
1. Insure removal of power from the unit per
4. Loosen the tube cap set screw and remove the
paragraph 5.10.2.
tube cap from the tube.
2. Remove front cover; loosen control panel
5. Loosen retaining clamp at the base of tube.
captive screws and swing control panel into its service
6. Pull the tube from the tube base assembly.
position.
7. Reinstall using the reverse of the above.
3. Remove  the  IF  Amplifier  Assembly  per
5.10.2.2 Magnetron Oscillator V2.  - See Figure 5-1:
paragraph 5.10.2.7 using steps 1,2,3,6 and 7.
refer to assembly drawings in Chapter 6, Section 6.2 as
necessary.
5-19






Western Governors University
< Previous Page
Index ^
Next Page >

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.