TM 11 -5840-360-24P
Code
Application/Explanation
ure is expressed by a two-character alphabetical
abbreviation (e.g., ea, in, pr, etc.). When the unit of
D-Support items that are removed, replaced, used at
measure differs from the unit of issue, the lowest unit of
depot, mobile depot, specialized repair
issue that will satisfy the required units of measure will
activity only.
(b) The maintenance code entered in the fourth
be requisitioned.
h. Quantity Incorporated in Unit. Indicates the
position indicates whether the item is to be repaired and
quantity of the item used in the breakout shown on the
identifies the lowest maintenance level with the capability
illustration figure, which is prepared for a functional
to perform complete repair (i.e., all authorized
group, subfunctional group, or an assembly.
maintenance functions). This position will contain one of
the following maintenance codes:
4. Special Information
Code
Application/explanation
a. The following publication pertains to the
AN/SPS-64(V)5 and its components:
D-The lowest maintenance level capable of complete
TM 11-5840-360-14-2, Radar Set, AN/SPS-64(V)5,
repair of the support item is the depot level.
Volume 2, Motion/Anti-Collision.
b. National stock numbers (NSN's) that are missing
Z-Nonreparable. No repair is authorized.
(3) Recoverability code. Recoverability codes are
from P source coded items have been applied for and
assigned to support items to indicate the disposition
will be added to this TM by future change/revision when
action on unserviceable items. The recoverability code is
they are entered in the Army Master Data File (AMDF).
entered in the fifth position of the Uniform SMR Code
Until the NSN's are established and published, submit
format as follows:
exception requisitions to: Commander, US Army
Recoverability
Communications-Electronics Command and
Fort
codes
Definition
Monmouth, ATTN: DRSEL-MM, Fort Monmouth, New
Jersey 07703 for the part required to support your
Z-Nonreparable item.
When unserviceable,
equipment.
condemn and dispose at the level indicated in position 3.
A-Item requires special handling or condemnation
procedures because of specific reasons (i.e., precious
5. How to Locate Repair Parts
metal content, high dollar value, critical material or
a When National stock number or part number is
hazardous
material).
Refer
to
appropriate
unknown.
manuals/directives for specific instructions.
(1) First. Using the table of contents, determine
c. National Stock Number. Indicates the National
the functional group within which the item belongs. This
stock number assigned to the item and will be used for
is necessary since illustrations are prepared for
requisitioning purposes.
functional groups and listings are divided into the same
d. Federal Supply Code for Manufacturer (FSCM).
groups.
The FSCM is a 5digit numeric code listed in SB 708-
(2) Second Find the illustration covering the
41/42 which is used to identify the manufacturer,
functional group to which the item belongs.
distributor, or Government agency, etc.
(3) Third Identify the item on the illustration and
e. Part Number. Indicates the primary number used
note the illustration figure and item number of the item.
by the manufacturer (individual, company, firm,
(4) Fourth Using the Repair Parts Listing, find
corporation, or Government activity), which controls the
the figure and item number noted on the illustration.
design and characteristics of the item by means of its
b. When National stock number or part number is
engineering drawings, specifications, standards, and
known.
inspection requirements to identify an item or range of
(1) First. Using the Index of National Stock
items.
Numbers and Part Numbers, find the pertinent National
NOTE
stock number or part number. This index is in NIIN
When a stock numbered item is
sequence followed by a list of part numbers in
requisitioned, the repair part received
alphameric sequence, cross-referenced to the illustration
may have a different part number than
figure number and item number.
(2) Second After finding the figure and item
the part being replaced.
f. Description Indicates the Federal item name and,
number, locate the figure and item number in the repair
if required, a minimum description to identify the item.
parts list.
g. Unit of Measure (U/M). Indicates the standard of
the basic quantity of the listed item as used in performing
6. Abbreviations
the actual maintenance function. This meas-
Not applicable.
(Next printed page is 4)
2
Previous Page
