• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print

Home > Radar Maintenance and Parts Manuals > > RADAR SET AN/SPS-64(V)2
Table 1-3 Radar Set AN/SPS-64(V) 1, (V)2 and (V)3 Recommended Test Equipment, Tools and Materials
Figure 1-4 Radar Set AN/SPS-64(V)2 Major Units

TM-11-5840-360-14-1-1 Radar Set AN/SPS-64(V)5 (NSN 5840-01-034-3946) Manual
Page Navigation
  5    6    7    8    9  10  11    12    13    14    15  
TM 11-5840-360-14-1-1
1.7 RADAR SET AN/SPS-64(V)2
Table 1-4 Radar Set
The Dual (Partial) System uses one 12-inch
AN/SPS-64(V)1, (V)2, (V)3
indicator, one 16-inch indicator, one antenna pedestal,
Recommended Spares
and two receiver transmitters, essentially the same as
the primary radar components described in paragraph
1.6. One six-position switching unit SA-2156 is used to
Azimuth Range Indicator
Part Number
Qty.
select the various operating modes of the system. The
Indicator
Dual (Partial) System allows the use of two indicators
Sweep Drive PCB
589436-1
1
with a single antenna by the addition of three interface
Position Transmission PCB
589412-1
1
equipments; the interface unit J-3463, the video
Sweep Generator PCB
589415-1
1
amplifier A/i-6932 and the waveguide switch SA-2140.
Timing Control PCB
589418-1
1
Refer to Figure 1-4 for illustrations of the units that
Data Storage PCB
589421-1
1
comprise the system.
Counter PCB
589424-1
1
Video Amplifier PCB
589430-1
1
1.7.1 Equipment Supplied (V2)
Control PCB
166133-1
1
Table 1-5 lists the equipment supplied with the Radar
VRM PCB
167520-1
1
Set AN/SPS-64 (V) 2.
CKT Card Extender PCB
589556-1
1
Lamps
277-1011P2
1
HV Regulator PCB
166165-1
1
1.7.2 Equipment Required But Not Supplied (V2)
Fuse, 5A
226-7176P57
2
Table 1-6 lists the cable and waveguide required but
Fuse, 4A
226-7177P14
2
not supplied for Radar Set AN/SPS64 (V) 2.
Fuse, 6A
226-7176P58
2
PRF Generator PCB
589427-1
1
1.7.3 Block Diagram Description (V2)
Figure 1-5 is a block diagram showing the major
NSK
components of Radar Set AN/SPS-64(V)2.
These
components are functionally identical to those described
Resolver Drive PCB
167688-1
1
in paragraph 1.6.3.  The primary advantages of this
Exciter PCB
167211-1
1
system are the presence of an additional indicator and
Stepper Motor
315-7243P1
1
the redundancy of the receiver transmitter and video
Receiver Transmitter
amplifier. This redundancy enhances system reliability
and availability. Depending on the mode of operation,
Modulator Tube,
as selected at the interface unit one indicator acts as the
Type 4PR6SOC
589752-1
1
master, the other as a slave unit. Only one receiver
Magnetron, Type M5149
167542-1
1
transmitter and video amplifier will be active at any
T/R Limiter
166083-1
1
given time to drive either or both of the indicators. The
Relay
589648-2
1
Dual (Partial) system is remotely controlled by the
Relay
165584-1
1
switching  unit;  the  control  circuits  are  positive
Relay
165043-1
1
command, latch-up, with limit switches that indicate
X-Band Gunn Oscillator
589364-1
1
when waveguide switching is completed.
Control PCB
166489-1
1
Pulse Drive PCB
166380-1
1
Delco 2N3902
18-212
1
1.7.4 Performance Characteristics (V2)
RCA 65115
588150-2
1
Performance characteristics for specific equipment
Diode 1N415D
167579-11
4
are found in the reference paragraph listed below:
Fuse, 3A
226-7176P68
2
Fuse, 5A
226-7177P15
2
Fuse, 1.5A
226-7177P26
2
Fuse, 10A
226-7181P2
1
Antenna
Drive Belt
167591-1
2
O-Ring
167636-1
1
Magnet
320-7180P3
1
Reed Relay
271-7247PI
1
Resolver
315-7243P2
1
Antenna Drive Motor
167666-1
1
1-9






Western Governors University
< Previous Page
Index ^
Next Page >

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.