TM 11-5840-360-14-1-1
Table 1-9 Radar Set AN/SPS-64 (V) 4 Equipment Supplied
Qty.
Model
Description
Product Code
1
RT-1240/SPS-64(V)
Receiver Transmitter, Radar
M27550
1
RT-1241/SPS-64(V)
Receiver Transmitter, Radar
M27551
1
AS-3194/SPS-64 (V)
Antenna
M27409
1
AB-1247A/SPS-64(V)
Pedestal, Antenna
M27576
1
AS-3195/SPS-64 (V)
Antenna
M27475
1
AB-1248/SPS-64(V)
Pedestal, Antenna
M27578
2
C-10260/SPS-64(V)
Control Indicator
M27603
1
AM-6933/SPS-64(V)
Amplifier-Generator
M27600
2
IP-1283/SPS-64(V)
Indicator, Azimuth Range
M27502
1
IP-1282/SPS-64(V)
Indicator, Azimuth Range
M27501
2
SA-2139/SPS-64(V)
Switching Unit
M27455
1
AM-6932/SPS-64(V)
Amplifier, Video
M27456
1
CV-3442/SPS-64(V)
Converter, Signal Data
M27602
signals and lines to the correct interfaces for the
Table 1-10 Radar Set AN/SpS64(V)4 Equipment
AN/SPA indicators. The signal data converter includes
Required But Not Supplied
all power supplies required for the conversion and
amplification circuits and presents a single interface to
Cable
Waveguide
Type
the switching unit. The control indicators interface with
X
Belden 8777
additional controls required to operate the AN/SPA
X
Belden 8769
indicators. To retain the AN/SPA bearing features,
X
Belden 9253
synchros are added to both antenna pedestals to
X
Belden 9773
provide appropriate bearing signals to the selected
X
Belden 9775
configuration mode.
X
RG-59A/U
X
RG-67/U
1.9.4 Performance Characteristics (V4)
X
FSGA-9
Performance characteristics for specific equipment
X
MSCA-7
of Radar Set AN/SPS-64(V)4 are found in the reference
X
TSGA-3
paragraphs listed below:
X
TSGA-4
X
TTRSA-4
Equipment
Paragraph
X
7/8 in EIA
Receiver Transmitter
RT-1240
Antenna AS-3194 & Pedestal AB-1247
The AN/SPS-64(V)4 radar system uses one 12inch
Indicators
IP 1282 & 1283
and two 16-inch azimuth range indicators, two antennas
Switching Unit
SA-2139
and antenna pedestals (X-band and S-band), and two
Video Amplifier
AM-6932
receiver transmitters (X-band and S- band). The system
Receiver Transmitter
RT-1241
also includes the signal data converter, two control
Antenna AS-3195 & Pedestal AB-1248
indicators, an amplifier-generator, and two switching
Signal Data Converter CV-3442
units. The switching units select the required antenna
Control Indicator
C-10260
synchro signals appropriate to the selected configuration
Amplifier - Generator
AM-6933
mode.
1.9.5 Required Test Equipment and Tools
The existing AN/SPA indicators and the AN/ SLA-10
Required test equipment and tools are listed in
ESM Blanking system are configured into the AN/SPS-
64(V)4 system via the signal data converter which
accepts video, trigger, and synchro signals from the
1.9.6 Recommended Spares
selected antenna, and all other required signals with the
Spares are listed in Table 1-12.
same characteristics used by the AN/SPS-64(V)4
indicators. The sight data converter unit converts all
1-18
Previous Page
