TM 11-5840-281-35/1
43 Shaft coupling (MP9115)
1 Screw (MP9102H1)
44 Screw (MP911H1)
2 Lockwasher (MP9102H1)
45 Cam (MP9111)
3 Flat washer (MP9102H1)
46 Screw (MP9110H4)
4 Rod End (MP9102)
47 Mounting bracket (MP9110)
5 Screw (MP9118H10)
48 Screw (MP9112H1)
6 Lockwasher (MP9118H10)
49 Cam (MP9112)
7 Flat washer (MP9118H10)
50 Screw (MP9119H4)
8 Actuator cover (MP9118)
51 Cover (MP9119)
9 Gasket (MP9123)
52 Gearshaft (MP9127)
10 Ring gasket (MP9122)
53 Bearing (MP9107)
11 Screw (MP9117H4)
54 Retaining ring (MP9134)
12 Actuator cover (MP9117)
55 Pin (MP9127-1H1)
13 Special cable assembly (W91
56 Helical gear (MP9127-1)
14 Cable (W9101-1)
57 Shaft (MP9127-2)
15 Connector (P1002/P504)
58 Screw (MP9120H5)
16 Rubber grommet (MP9128)
59 Cover (MP9120)
17 Nut (MP9114H1)
60 Retaining ring (MP9134)
18 Screw (MP9114H1)
61 Spur gear (MP9126)
19 Flat washer (MP9114H1)
62 Sleeve bearing (MP9106)
20 Clamp (MP9114)
63 Fastener stud (MP9143)
21 Nut (MP9121H2)
64 Retaining ring (MP9136)
22 Screw (MP9121H2)
65 Spur gear (MP9125)
23 Flat washer (MP9121H2)
66 Retaining ring (MP9135)
24 Rf filter (MP9121)
67 Key (MP9129)
25 Screw (MP9150H4)
68 Screw (MP9116H4)
26 Dc motor (MP9150)
69 Cover (MP9116)
27 Screw (MP9144H2)
70 Shim (MP9141)
28 Screw (MP9144H2)
71 Worm shaft (MP9140)
29 Switch actuator (MP9105)
72 Bearing (MP9109)
30 Switch (MP9144)
73 Ram tube assembly (MP9145)
31 Screw (MP9132H2)
74 Bearing (MP9108)
32 Cover plate (MP9132)
75 Flat washer (MP9147)
33 Screw (MP9144H2)
76 Helical gear (MP9124)
34 Screw (MP9144H2)
77 Key (MP9130)
35 Switch actuator (MP9105)
78 Screwjack (MP9108)
36 Switch (MP9144)
79 Bearing (MP9108)
37 Screw (MP9132H2)
80 Seal (MP9139)
38 Cover plate (MP9132)
81 End cap (MP9113)
39 Setscrew (MP9115H2)
82 Preformed packing (MP9131)
40 Nut
83 Tube-gearbox (MP9146)
41 Lockwasher
42 Variable resistor (MP9133)
Figure 5-7.--Continued
(38) Install rubber grommet (16) on actuator cover
(44) Attach actuator cover (12) to tube-gearbox
(12).
(83) using four screws (11).
(39) If cable (14) or connector (15) were replaced,
(45) Slide ring gasket (10) on tube-gearshaft (83),
assemble new special purpose cable (13) from cable
then attach actuator cover (8) and gasket (9) to actuator
(14) and connector (15).
cover (12) using 10 screws (5), lockwashers (6), and flat
(40) Feed special purpose cable (13) through
washers (7).
rubber grommet (16).
(46) Attach rod end (4) to actuator cover (12) using
(41) Connect wires from special purpose cable (13)
screw (1), lockwasher (2), and flat washer (3).
to switches (30 and 36) and variable resistor (42) as
(47) Check operation of servo actuator in accord-
shown on schematic of antenna servo actuator (fig. 7-
ance with procedure.
68).
(42) Connect wires between switches (30 and 36),
5-13.
Disassembly and Assembly
of
Azimuth
rf filter (24), and dc motor (26) as shown on schematic of
Antenna Drive TG-1 13/TPN-8
antenna servo actuator (fig. 7-68).
(43) Attach clamp (20) to special purpose cable
(13), then, while holding actuator cover (12) in position
a. Disassembly. To disassemble azimuth Antenna
on tube-gearbox (83), dress cable along cover and
Drive TG-113/TPN-8, proceed as follows:
secure clamp to cover using nut (17), screw (18), and flat
washer (19).
5-25
Previous Page
