TM 11-5840-281-35/1
1 Screw (MP9320H4)
37 Lockwasher (MP9301H6)
2 Lockwasher (MP9320H4)
38 Flat washer (MP9301H6)
3 Flat washer (MP9320H4)
39 Polarizer support (MP9301)
4 Setscrew (MP9308)
40 Reflector (MP9307)
5 Horn and polarizer (MP9320)
41 Plug (MP9307-1)
6 Nut (MP9303H1)
42 Screw (MP9373H6)
7 Screw (MP9303H1)
43 Latch (MP9373)
8 Lockwasher (MP9303H1)
44 Screw (MP9368H4)
9 Flat washer (MP9303H1)
45 Lockwasher (MP9368H4)
10 Clamp (MP9303)
46 Flat washer (MP9368H4)
11 Nut (MP9361H1)
47 Actuator support (MP9368)
12 Screw (MP9361H3)
48 Waveguide coupling (MP9362)
13 Lockwasher (MP9361H3)
49 Cover (MP9363)
14 Flat washer (MP9361H3)
50 Screw (MP9363-1H1)
15 Clamp (MP9361)
51 Wire rope assembly (MP9363-1)
16 Screw (MP9305H3)
52 Screw (MP9370H4)
17 Lockwasher (MP9305H3)
53 Lockwasher (MP9370H4)
18 Flat washer (MP9305H3)
54 Flat washer (MP9370H4)
19 Pin (MP9305H2)
55 Waveguide (MP9370)
20 Clinometer mount (MP9305)
56 Preformed packing (MP9365)
21 Screw (MP9304H2)
57 Screw (MP9366H4)
22 Flat washer (MP9304H2)
58 Lockwasher (MP9366H4)
23 Flat washer (MP9304H1)
59 Flat washer (MP9366H6)
24 Scope mount (MP9304)
60 Ring (MP9366)
25 Screw (MP9302H2)
61 Gasket (MP9364)
26 Lockwasher (MP9302H2)
62 Screw (MP9369H3)
27 Flat washer (MP9302H2)
63 Nonmetallic washer (MP9369HS)
28 Flat washer (MP9302H1)
64 Retaining strap (MP9367)
29 Mounting bracket (MP9302)
65 Nut (MP9369-1H2)
30 Nut (MP9306H4)
66 Pin (MP9369-1)
31 Screw (MP9306H4)
67 Waveguide (MP9369)
32 Lockwasher (MP9306H4)
68 Screw (MP9361H3)
33 Flat washer (MP9306H4)
69 Lockwasher (MP9361H8)
34 Identification plate (MP9306)
70 Flat washer (MP9361H3)
35 Nut (MP9301H6)
71 Clamp (MP9361)
36 Bolt (MP9O01H6)
72 Yoke (MP9372)
Figure 5-4. Continued
(47) using nut (11), screw (12), lockwasher (13), and flat
NOTE
washer (14).
Open end of waveguide (55) must point away
(11) Attach two latches (43) to yoke (72) using
from actuator support (47).
three screws (42).
(12) Attach two pins (66) to waveguide (67) with
(16) Attach clamp (71) on yoke (72) using
nuts (65).
screws (68), lockwashers (69), and flat washers (70).
(13) Position waveguide (67) inside yoke (72)
(17) Attach wire rope assembly (51) to
and secure in place using three screws (62), nonmetallic
waveguide coupling (48).
washers (63), and two retaining straps (64).
(18) Attach wire rope assembly (51) to cover
(49) using screw (50).
(19) Attach waveguide coupling (48) to
NOTE
waveguide (55).
Retaining straps (64) are not required to secure
(20) Install cover (49) over open waveguide (55)
waveguide (67) but are installed here to hold
and secure in place with waveguide coupling (48).
connector covers when the radar set is
operational.
5-9.
Disassembly and Assembly of Azimuth Horn
(14) Attach ring (60) and gasket (61) to yoke (72)
using four screws (57), lockwashers (58), and flat
washers (59).
a. Disassembly. To disassemble azimuth horn and
(15) Place preformed packing (56) in position on
polarizer, proceed as follows:
waveguide (67) then attach waveguide (55) using four
(1) Remove nut (1), screw (2), lockwasher (3),
screws (52), lockwashers (53), and flat washers (54).
and two flat washers (4).
5-7
Previous Page
