TM 11-5840-281-35/1
(12) Remove screw (43), lockwasher (44), and
NOTE
flat washer (45).
Screw (67) has been drilled out to fit
(13) Remove nut (46), screw (47), lockwasher
over the pin in cover (73).
(48), flat washer (49), switch (50) and adjusting plate
(51).
(5) Attach switch (50) to adjusting plate (51)
(14) Remove four screws (52), lockwashers (53),
using nut (46), screw (47), lockwasher (48), and flat
flat washers (54), terminal board (55), and label (56).
washer (49).
(15) Remove eight screws (57), lockwashers
(6) Attach assembled switch (50) and adjusting
(58), and flat washers (59).
plate (51) to cover (73) using screws (40 and 43),
(16) Remove cover with actuator attached from
lockwashers (41) and 44), and flat washers (42 and 45).
housing.
(7) Position adjusting plate (51) so switch (50) is
(17) Remove gasket (60).
as far from plunger (72) as possible.
(18) Remove cotter pin (61), pin (62), and
(8) Attach switch (38) to adjusting plate (39)
actuator (63).
using nut (34), screw (35), lockwasher (36), and flat
washer (87).
(9) Attach assembled switch (38) and adjusting
NOTE
plate (39) to cover (73) using screws (28 and 31),
Refer to paragraph 5-20 for disassembly
lockwashers (29 and 32), and flat washers (30 and 33).
procedures for the actuator assembly.
(10) Position adjusting plate (39) so switch (38)
is as far from plunger (72) as possible.
(19) Remove four screws (64), lockwashers (65),
flat washers (66), screws (67 and 68), blocks (69), and
springs (70).
NOTE
(20) Remove pins (71) and plunger (72) from
Switches (38 and 50) will be adjusted
cover (78).
during system alignment.
(21) Remove screw (74), lockwasher (75), flat
washer (76), and retaining strap (77).
(11) Attach label (56) and terminal board (55) to
(22) Remove four screws (78), lockwashers (79),
cover (73) using four screws (52), lockwashers (53), and
flat washers (80), connector (81), and gasket (82).
flat washers (54).
(23) Remove two connector covers (883), four
screws (84), lockwashers (85), flat washers (86),
NOTE
connector (87), and gasket (88).
Label (56) should be oriented so the
(24) Remove four screws (89), lockwashers (90),
number "1" is at the top.
flat washers (91), connector (92), and gasket (93).
(25) Remove six screws (94), lockwashers (95),
(12) Attach 100-350 actuator (63) to plunger
five flat washers (96), connector mounting plate (97), and
(72) using pin (62) and cotter pin (61).
gasket (98) from housing (99).
(13) Feed cable from 10-35 actuator through
b. Assembly. To assemble the 10-35 actuator
cover (73), then, using schematic of elevation drive
assembly, proceed as follows:
assembly as a guide (fig. 7-66), connect wires from
(1) Insert pins (71) into plunger (72), then install
cable to terminal board TB508 (55).
plunger in cover (73).
(14) Using schematic of elevation drive
(2) Slide springs (70) between pins (71) and
assembly as a guide (fig. 7-66), connect wires between
hook holes in end of springs over pin in cover (73).
terminal board TB503 (55) and switches (38 and 50).
(3) Attach two blocks (69) to cover (78) using
(15) Using schematic of elevation drive
two screws (64), lockwashers (65), and flat washers (66)
assembly as a guide (fig. 7-66), connect the required
for each block.
wires to terminal board TB503 (55) and switches (38 and
(4) Install screws (67 and 68) into blocks (69) to
50), then feed wires through cover (78).
secure springs (70) in place.
(16) Place gasket (60) on housing (99), then
install 10-35 actuator (63) in housing, positioning cover
(73) in place.
5-51
Previous Page
