TM 11-5840-281-35/1
1
Nut (MP580-2)
51
Adjusting plate (MP694)
2
Rod end (MP580-4)
52
Screw (TBS03H4)
3
Nut (MP580-1)
53
Lockwasher (TB50OH10)
4
Rod (MP580-3)
54
Flat washer (TB503H4)
5
Retaining ring (MP581H2)
55
Terminal board (TBSOS3)
6
Bearing (MPS81)
56
Label (MP691)
7
Shaft (MP582)
57
Screw (MPS88H8)
8
Arm assembly (MP580)
58
Lockwasher (MP688H8)
9
Nut (MP582H2)
59
Flat washer (MP688H8)
10
Screw (MP582H2)
60
Gasket (MP588A)
11
Lockwasher (MP5842H2)
61
Cotter pin (B04H1l)
12
Flat washer (MP584H2)
62
Pin (B604H11)
13
Block (MP584A)
63
10'-35 Actuator (B5604)
14
Block (MPS84B)
64
Screw (MP5856H4)
15
Screw (MP587H2)
65
Lockwasher (MP585H4)
16
Lockwasher (MP587H2)
66
Flat washer (MP585H4)
17
Flat washer (MP587H2)
67
Screw (MP585H1)
18
Pin (MP587H1)
68
Screw (MP685H1)
19
Slide cover (MP587)
69
Block (MP585)
20
Pin (MPS79H1)
70
Spring (MP597)
21
Slide (MP583)
71
Pin (MP965H2)
22
Washer (MP598)
72
Plunger (MP595)
23
Screw (MP589H8)
78
Cover (MP588)
24
Lockwasher (MP589H8)
74
Screw (MP596H1)
26
Flat washer (MP589H8)
75
Lockwasher (MP596H1)
26
Cover (MP589)
76
Flat washer (MP596H1)
27
Gasket (MP589A)
77
Retaining strap (MP596)
28
Screw (S504H1)
78
Screw (J503J4)
29
Lockwasher (S504H2)
79
Lockwasher (J6503H4)
30
Flat washer (S504H2)
80
Flat washer (J503H4)
31
Screw (MP59
3H1)
81
Connector (J503)
32
Lockwasher (MP593H1)
82
Gasket (J63503A)
33
Flat washer (MP593H1)
88
Connector cover (MP586)
34
Nut (S504H1)
84
Screw (JS04H4)
35
Screw (S504H1)
85
Lockwasher (J504H4)
36
Lockwasher (5504H2)
86
Flat washer (J504H4)
37
Flat washer (S504H2)
87
Connector (3504)
38
Switch (S504)
88
Gasket (J3504A)
39
Adjusting plate (MP593)
89
Screw (J605H4)
40
Screw (S505H1)
90
Lockwasher (J505H4)
41
Lockwasher (S605H2)
91
Flat washer (J6505H4)
42
Flat washer (S505H2)
92
Connector (J5605)
48
Screw (MP594H1)
93
Gasket (J0S6A)
44
Lockwasher (MP594H1)
94
Screw (MP592H6)
46
Flat washer (MP594H1)
95
Lockwasher (MP592H6)
46
Nut (S506H1)
96
Flat washer (MP592HS)
47
Screw (SOSH1)
97
Connector mounting plate (MP592)
48
Lockwasher (S505H2)
98
Gasket (MPB92A)
49
Flat washer (S505H2)
99
Housing (MP590)
50
Switch (S56065)
Figure 5.--Continued
(21) Install pin (18) through slide cover (19) into
NOTE
housing (99).
The assembled rod (4) and arm
(22) Install pin (20) through slide (21) into 105
assembly (8) will be adjusted during
actuator (63) shaft.
system alignment.
(23) Position arm assembly (8) on slide (21),
then install shaft (7) through arm assembly and shaft.
(27) Attach connector (81) and gasket (82) to
(24) Install bearings (6) on each end of shaft (7)
connector mounting plate (97) using four screws (78),
and secure in place with retaining rings (5).
lockwashers (85), and flat washers (86).
(25) Screw nut (3) on arm assembly (8), then
(28) Attach connector (92) and gasket (93) to
screw rod (4) on arm assembly.
connector mounting plate (97) using four screws (89),
(26) Screw nut (1) on rod end (2), then screw rod
lockwashers (90), and flat washers (91).
end into rod (4).
(29) Attach connector (87) and gasket (88) to
connector mounting plate (97) using four screws (84),
5-53
Previous Page
