TM 11-5840-281-35/1
46 Guard (MP9206)
1 Nut (MP9228H2)
47 Screw (MP92229H3)
2 Screw (MP9228H2)
48 Lockwasher (MP9229H3)
3 Lockwasher (MP9228H2)
49 Flat washer (MP9229H3)
4 Flat washer (MP9228H2)
50 Pin (MP9229H2)
5 Clamp (MP9228)
51 Clinometer mount (MP9229)
6 Nut (MP9227H2)
52 Screw (MP9211H3)
7 Screw (MP9227H2)
53 Lockwasher (MP9211H3)
8 Lockwasher (MP9227H2)
54 Flat washer (MP9211H3)
9 Flat washer (MP9227H2)
55 Wire rope assembly (MP9211)
10 Bracket (MP9225)
56 Pin (A9100H1)
11 Clamp (MP9227)
57 Pin (A9100H1)
12 Screw (MP9226H2)
58 Actuator (A9100)
13 Lockwasher (MP9226H2)
59 Nut (MP9210H1)
14 Flat washer (MP9226H2)
60 Rod end (MP9210)
15 Clamp (MP9226)
61 Retaining clip (MP9204)
16 Screw (MP9221H2)
62 Nut (MP9205H4)
17 Lockwasher (MP9221H2)
63 Screw (MP9205H4)
18 Flat washer (MP9221H2)
64 Lockwasher (MP9205H4)
19 Screw (MP9222H2)
65 Flat washer (MP9205H4)
20 Lockwasher (MP9222H2)
66 Dial (MP9205)
21 Flat washer (MP9222H2)
67 Plug (MP9231-1)
22 Screw (MP9223H2)
68 Reflector (MP9231)
23 Lockwasher (MP9223H2)
69 Screw (MP9202H4)
24 Flat washer (MP9223H2)
70 Lockwasher (MP9202H4)
25 Pin (MP9240H6)
71 Flat washer (MP9202H4)
26 Elevation horn and polarizer (MP9240)
72 Actuator bracket (MP9202)
27 Spherical nut (MP9230)
73 Screw (MP9209H2)
28 Nut (MP9224H3)
74 Lockwasher (MP9202H2)
29 Pin (MP9224H3)
75 Flat washer (MP9209H2)
30 Ball joint (MP9224)
76 Pointer (MP9209)
31 Arm (MP9221)
77 Pin (MP9212-1H1)
32 Arm (MP9222)
78 Lower pivot (MP9212-1)
33 Arm (MP9223)
79 Pin (MP9212-2H1)
34 Screw (MP9207H2)
80 Upper pivot (MP9212-2)
35 Flat washer (MP9207H2)
81 Screw (MP9203H2)
36 Flat washer (MP9207H1)
82 Lockwasher (MP9203H2)
37 Scope mount (MP9207)
83 Flat washer (MP9203H2)
38 Screw (MP9201H4)
84 Clamp (MP9203)
39 Lockwasher (MP9201H4)
85 Screw (MP9208H4)
40 Flat washer (MP2901H4)
86 Lockwasher (MP9208H4)
41 Flat washer (MP9201H3)
87 Flat washer (MP9208H4)
42 Bracket (MP9201)
88 Identification plate (MP9208)
43 Screw (MP9206H2)
89 Yoke (MP9212)
44 Lockwasher (MP9206H2)
45 Flat washer (MP9206H2)
Figure 5-6.--Continued
(14) Remove screw (46), lockwasher (47), and cam
(48).
washers (87), setscrews (88), shaft (89), and bracket
(15) Remove screw (49), lockwasher (50, and cam
(90).
(51).
(23)
Disconnect terminals (92) from terminal
(16) Remove four screws (52), lockwashers (53),
boards.
flat washers (54), motor (55), pin (56), and spur gear
(24) Remove bushing (93) and connector (94) from
(57).
cable (95).
(17) Remove two nuts (58), lockwashers (59), flat
(25) Remove two screws (96), lockwashers (97),
washers (60), and setscrews (61).
flat washers (98).
(18) Remove four screws (62), lockwashers (63),
(26) Remove two screws (100), lockwashers (101),
two adapters (64), and switches (65, 66, 67, and 68).
flat washers (102), and terminal board (103).
(19) Remove two screws (69), lockwashers (70),
(27) Remove screw (104), lockwasher (105), flat
flat washers (71), and spacer (72).
washer (106), cover plate (107), gasket (108), and four
(20) Remove two screws (73), lockwashers (74),
plugs (109) from housing (110).
flat washers (75), and spacer (76).
b. Assembly.
To assemble elevation horn and
(21) Remove retaining ring (77), three screws (78),
polarizer, proceed as follows:
spacer (82), idler gear (83), and two spacers (84).
(1) Insert four rubber plugs (109) into housing
(110).
5-17