TM 11-5840-281-35/1
56 Pin (MP9261-1H1)
1 Waveguide coupling (MP9249)
57 Spur (ear (MP9261-1)
2 Screw (MP9251-1H1)
58 Nut (MP9272H2)
3 Pin (MP9251-1H1)
59 Lockwasher (MP9272H2)
4 Wire rope assembly (MP9251-1)
60 Flat washer (MP9272H2)
5 Cover (MP9251)
61 Setscrew (MP9272)
6 Preformed packing (MP92638)
62 Screw (MP9241H4)
7 Screw (MP9283H6)
63 Lockwasher (MP9241H4)
8 Lockwasher (MP9283H6)
64 Adapter (MP9241)
9 Flat washer (MP9283H5)
65 Switch (S9202)
10 Waveguide (MP9283)
66 Switch (S9201)
11 Spacer (MP9280)
67 Switch (S9203)
12 Preformed packing (MP9262)
68 Switch (S9204)
13 Ring (MP9270)
69 Screw (MP9278H2)
14 Linkage (MP9260)
70 Lockwasher (MP9278H2)
15 Choke (MP9248)
71 Flat washer (MP9278H2)
16 Transition (MP9282)
72 Spacer (MP9278)
17 Transition (MP9281)
73 Screw (MP9279H2)
18 Cover (MP9250)
74 Lockwasher (MP9279H2)
19 Screw (MP9258H6)
75 Flat washer (MP9279H2)
20 Lockwasher (MP9258H6)
76 Spacer (MP9279)
21 Flat washer (MP9258H6)
77 Retaining ring (MP9269)
22 Horn (MP9258)
78 Screw (MP9247H3)
23 Setscrew (MP9274)
79 Lockwasher (MP9247H3)
24 Screw (MP9264H3)
80 Flat washer (MP9257H3)
25 Lockwasher (MP9264H3)
81 Spur gear (MP9257)
26 Flat washer (MP9264H3)
82 Spacer (MP9277)
27 Phase section (MP9264)
83 Idler gear (MP9256)
28 Screw (MP9265H3)
84 Spacer (MP9276)
29 Lockwasher (MP9265H3)
85 Screw (MP9244H2)
30 Flat washer (MP9265H3)
86 Lockwasher (MP9244H2)
31 Phase section (MP92656)
87 Flat washer (MP9244H2)
32 Screw (MP9266H24)
88 Setscrew (MP9273)
33 Channel (MP9243)
89 Shaft (MP9275)
34 Screw (MP9242H16)
90 Bracket (MP9244)
35 Block (MP9242)
91 Cable assembly (W9201)
36 Plate (MP9266)
92 Terminal (W9201-2)
37 Ring (MP9271)
93 Bushing (MP9245)
38 Gasket (MP9253)
94 Connector (P505)
39 Nut (MP9252H3)
95 Cable (W9201-1)
40 Screw (MP9242H3)
96 Screw (TB9201H2)
41 Screw (MP9242H7)
97 Lockwasher (TB9201H2)
42 Lockwasher (MP9242H10)
98 Flat washer (TB9201H2)
43 Flat washer (MP9242H10)
99 Terminal board (TB9201)
44 Cover (MP9252)
100 Screw (TB9202H2)
45 Gasket (MP9255)
101 Lockwasher (TB9202H2)
46 Screw (MP9247H1)
102 Flat washer (TB9202H2)
47 Lockwasher (MP9247H1)
103 Terminal board (TB9202
48 Cam (MP9247)
104 Lockwasher (MP9267H1)
49 Screw (MP9246H1)
105 Lockwasher (MP9267H1)
50 Lockwasher (MP9246H1)
106 Flat washer (MP9267H1)
51 Cam (MP9246)
107 Cover plate (MP9267)
52 Screw (MP9261H4)
108 Gasket (MP9254)
53 Lockwasher (MP9261H4)
109 Rubber plug (MP9268)
54 Flat washer (MP9261H4)
110 Housing (MP9259)
55 Dc motor (B9201
Figure 5-7.--Continued
(5) Refer to steps (2), (3), and (4), and assemble
(8) Attach horn (22) to phase sections (27 and 31)
two channels (33), two plates (36), and four blocks (35)
with six screws (19), lockwashers (20), and flat washers
in same manner on phase section (31).
(21), but do not tighten hardware.
(6) If cover (18) was removed from horn (22) or is
(9) Place ring (37) and gasket (38) on phase
being replaced, cement to horn with rigid-ratio mixture of
sections (27 and 31).
Resiweld No. 7004 or equivalent.
(10) Carefully ease phase sections (27 and 31) into
(7) Coat mating surfaces or horn (22) and phase
housing (110).
sections (27 and 31) with light film of silicone compound
DC-4.
5-19
Previous Page
