TM 11-5840-281-35/1
32 Lockwasher (B1002H4)
1 Plug (MP1080)
33 Flat washer (B1002H4)
2 Plug (MP1081)
34 Azimuth drive motor (B1002)
3 Gasket (MP1081A)
35 Nut (MP1006-1H10)
4 Nut (MP1068H1)
36 Screw (MP1066-1H11)
5 Screw (MP1068H1)
37 Lockwasher (MP10661H1)
6 Lockwasher (MP1068H1)
38 Flat washer (MP1066-1H11)
7 Flat washer (MP1068H1)
39 Cover (MP1066-1)
8 Screw (MP1068H4)
40 Gasket (MP1069)
9 Lockwasher (MP1068H4)
41 Bearing (MP1063)
10 Flat washer (MP1068H4)
42 Spur gearshaft (MP1071)
11 Screw (MP1068-1H1)
43 Bearing (MP1064)
12 Flat washer (MP1068-1H1)
44 Seal (MP1084)
13 Wire rope assembly (MP1068-1)
45 Screw (MP1086H4)
14 Cover (MP1068)
46 Sleeve (MP1086)
15 Fastener (MP1067H6)
47 Gasket (MP1086A)
16 Shipping cover (MP1067)
48 Retaining ring (MP1082)
17 Preformed packing (MP1077)
49 Spur gearshaft (MP1073)
18 Air deflector ring (MP1083)
50 Bearing (MP1062)
19 Preformed packing (MP1078)
51 Preformed packing (MP1076)
20 Screw (MP1085H3)
52 Spur gearshaft (MP1072)
21 Screw (MP1085H3)
53 Bearing (MP1064)
22 Lockwasher (MP1085H6)
54 Spur gearshaft (MP1070)
23 Flat washer (MP1085H6)
55 Bearing (MP1063)
24 Motor shield (MP1085)
56 Spur gearshaft (MP1074)
25 Preformed packing (MP1077)
57 Bearing (MP1063)
26 Connector cover (MP1066)
58 Screw (MP1079H4)
27 Screw (J1003H4)
59 Lockwasher (MP10791E4)
28 Lockwasher (J1003H4)
60 Instruction plate (MP1079)
29 Connector (J1003)
61 Gearcase housing (MP1066-2)
30 Gasket (J1003A)
31 Screw (B1002H4)
Figure 5-10.--Continued
(1) Remove eight screws (1) and lockwashers (2)
(16) Remove six screws (32), lockwashers (33),
attaching motor shroud assembly (3).
and end bell (34).
(2) Pull motor shroud assembly from motor.
(17) Remove flat washer (35) and bearing (36)
(3) Remove two setscrews (4) and impeller (5).
from armature shaft.
(4) Remove four screws (6), lockwashers (7), and
(18) Pull armature shaft assembly (37) out of
two brackets (8).
housing and remove spring tension washer (38), washer
(5) Remove four screws (9), lockwashers (10), and
(39), and bearing (40) from armature shaft.
end bell (11).
(19) Remove all wires from terminal boards on
(6) Remove retaining ring (12) from end bell.
motor housing.
(7) Remove spacer (13), spring tension washer
(20) Remove four screws (41), lockwashers (42),
(14), spacer(s) (15), and bearing (16) from rotor shaft.
terminal board (43), and terminal board support (44)
(8) Remove rotor (17) from motor assembly.
from motor housing.
(9) Remove washer (18), spacer(s) (19), and
(21) Remove four screws (45), lockwashers (46),
bearing (20) from rotor shaft.
terminal board (47), and terminal board support (48)
(10) Remove retaining ring (21) from housing.
from motor housing.
(11) Remove field assembly (22) from blower motor
(22) Remove four screws (49), lockwashers (50),
housing (23).
terminal board (51), and terminal board support (52)
(12) Remove identification plate (24) from end bell.
from motor housing.
(13) Remove four screws (25), lockwashers (26),
(23) Remove terminals (53) from wires.
end bell retainer (27), and end bell (28).
(24)
Remove two setscrews (54) and field
(14) Remove nut (29) and drag cup (30).
assembly (55) from motor housing.
(15) Remove field assembly (31) from end bell.
(25) Remove grommet (56) from motor housing.
(26) Remove four screws (57) and identification
plate (58) from motor housing (59).
5-37
Previous Page
